Options overview



Options for all series

Body connection with slip-on flanges

ATEX (EC - declaration of conformity)

Body connection with slip-on flanges

Elastomeres AED (Anti-Explosion Decompression type)

Externally barrelled

Externally electrolytically polished

Grounding device

Medium wetted elastomers ADI free

Medium wetted elastomers with FDA and USP Class VI 121°C certification

Medium wetted elastomers with FDA and USP Class VI certification

Medium wetted elastomers with FDA certification

Medium wetted inner parts DIN/EN 10204/3.1

Medium wetted parts with a delta-ferrite concentration < 0,5 % | < 1 % | < 1 % (weldings < 3%) | < 3 %

Oxygen design

Pickled and passivated - from DN 32 (1 1/4")

Pickled and passivated - up to DN 25 (1")

Spezial face to face dimension

Vacuum resistant design

Options for pressure control valves

Adjustable damping

Adjusting screw gasket

Adjusting screw sealable

Adjusting screw with adjustment protection (cap or similar)

Adjusting screw with anti-twist device

Adjusting screw with handwheel (metal)

Adjusting screw with handwheel (plastic)

Adjusting screw with travel limitation (split pin)

Angle design

Body made of solid metal

Changeable seat (≤ DN 25 / up to Kvs 0.4)

Closed spring cap

Compact actuator with protection cap

Cone and seat stellited

Cone hardened (lime wash design)

Cone stellited

Control room draining to the bottom

Damping (adjusting screw o-ring without lubricants)

Differential pressure regulation

Direct sense line

External surfaces from Ra ≤ 0,6, electropolished (weldings e

Flanges with raised face Ra < 0,8 µm

Flow controlling

Flow direction from right to left

Flow limiter

Force limiter

Free of oil and grease

Free of silicone

Gas spring connection without relief bore (electro-pneumatical control)

Gauge connection 1/2" |  1/4" 

Gauge connection aseptic design

Hydraulic damping (design for gases)

Inlet connection eccentric

Internal control bore

Kvs reduction

Leakage line connection  1/8"  | 1/4" |  3/8" 

Leakage line connection 1/8" & Damping (adjusting screw o-ring without lubricants)

Medium wetted parts according to NACE

Medium wetted surfaces from Ra ≤ 0,25 µm, electropolished

Medium wetted weldings with a delta-ferrite concentration < 3 %

Mid section for steam up to 200°C | 220 °C | 250°C | 300°C | 400°C with filling plug and sense line connection

Nickel-plated version for air and liquids up to 100°C

Piston controlled design

PN 40 | PN 63 |PN 100 | PN 160 design

Pneumatical lifting device (open position for SIP/CIP)

Reduced body

Sense line connection EO 8

Sense line connection in the mid section

Spring cap with bore in tube sheet (e.g. CO2 application)

Spring cap with damping bus

Straight-way design

Stroke arresting (open position for SIP/CIP)

Stroke limitation

TA-Luft / H2 design

Throttle cone

Vacuum controlling

Venting for installation with spring cap on top

Options for level control valves

Additional fitting at the side

Additional fitting connection

Additional fitting connection with plug

Additional fitting on the top

Adjustable permanent venting

Anti cavitation cone

Anti-shock device

Connection for frost protection

Design: Inflow, flow downwards (Z/u)

Design: Inflow, flow horizontal (Z/w)

Design: Inflow, flow upwards (Z/o)

Design: Outflow, flow downwards (A/u)

Design: Outflow, flow horizontal (A/w)

Design: Outflow, flow upwards (A/o)

DN 25 (based on DN 20)

Drain connection

Drain plug of stainless steel

Enlarged body

Enlarged float

Fitting at the body, at the bottom

Float lever rotated by 45° | 90°

Float made of stainless steel with PA coating

Float mounted downwards

Float Ra ≤ 1,6 µm, weldings - lap blasted

Float Rod L =  500 mm  | 1000 mm |  1500 mm  |  2000 mm 

Free of oil and grease

Free of silicone

High pressure design (PN40)

Installation horizontal

Lever extended

Lever position on top

Lifting and swivel device

Lifting device

Liquids (density > 450 kg/m³)/gases

Multi-bore orifice plate

Non return valve on the outlet

Non return valve on the outlet (PTFE ball)

Non-slam closing mechanism

Outlet with protection cover

PA coating

Parallel guide

PN 25 design

Reinforced design

Reinforced float

Rigid permanent venting nozzle

Sight glass to the left of the inlet

Special design without continuous venting

Thermal start up and permanent venting

Thermal start venting and rigid permanent venting

Venting connection: BSP male G 1/2" to the top

Without continuous venting

Without float rod

Without manual air valve, compensation line connection plugged

Without sealing plug

Without venting valve

Options for Pipeline Ancillaries

Cover lifting and pivoting device

Differential pressure display

External indicator

Filter insert P: 3 layer made of stainless steel 25 µm

Filter insert P: 3 layer made of stainless steel 5 µm

Filter insert S: sintered made of stainless steel 5 µm

Filter mat No. 60 (size of pores 0,265 mm)

Filter mat No. 80 (size of pores 0,150 mm)

Filter mat No. 80 (size of pores 0,370 mm)

Impeller up to 80°C

Internal flag

Quick-lock mechanism

Strainer mesh size 0.25 mm

Strainer mesh size 1 mm

Strainer mesh size 2.5 mm

Strainer mesh sizes 0.5 - 10 mm

Supporting feet

Contact
Product
Ricerca prodottiBitte Produktbezeichnung eingeben